S Kamiya

1022: Ryu Jin 1.64

| wonko

This started as pure procrastination – I had marking and reporting to do but ….

ryujun 1.64

Folded from a “live guide” photodiagram series produced by Daniel Brown, as part of a channel in a discord from another planet, irresistible as it is yet another variation of eastern dragon I knew I HAD to fold,

ryujun 1.64 development

This little fellow is nearly naked – apart from some glue to hold in a wire spine and wires for arms and legs, he is otherwise folded only (hence some of the wayward seams and flaps). I quite like this unfinished appearance and think he will stay as is.

ryujun 1.64 views

Folded from 90cm natural Kraft, it starts with a therapeutic 64 grid on the diagonal and goes to hell in a handbasket from then on. The basic folding is quite straight forward (as a Ryu master), this variation is a bit of a mashup between a 1.2 and the head of a 2.1 – the result is wonderfully complex and beautifully “Kamiya” in intent.

ryujun 1.64 scale

I decided to fold it in plain (both sides same) paper as the bi-color fold has a large gash of reverse side colour along the underside – I have used this to effect in both a 1.2 and a 2.1, so thought I would go differently this time. Interestingly (to me) this little chappie is folded with a sheet exactly 1/4 the size (and from the same paper roll) as my original 3.5 (a little Ryu Jin nerdistry there).

1016: World Origami Days – Bahamut

| wonko

World Origami Days is a period end October-beginning November that is an international celebration of Origami. I decided to try a super complex model (fold until it fails) and successfully folded Satoshi Kamiya’s “Divine Dragon (Bahamut)” on the first attempt:

Satoshi Kamiya's Bahamut

Rarely does a first fold work out but I kept folding and it did, much to my surprise and delight. The fold sequence is particularly punishing and describes a bit of an enigma of a model – the balance between paper thinness and size. I chose 80gsm 100cm square Kraft paper and at this size/thickness it was tough going in places indeed. The body and legs are incredibly thick compared to the single layer wings – a bit of a puzzle if you wanted to fold it small.

Satoshi Kamiya's Bahamut Views

A “Bahamut” is a monster from the “Final Fantasy” franchise, and is an odd mix of a lizard, dragon, Godzilla…thing.

The detail here is terrifying. Thick, muscular 4-toed feet, thick dragonny tail, chest sporting a 6 pack (make that a whole slab), arms with 4 claws, complex and snarly horned head and glorious wings with an extra set of hands atop them – quite a formidable beastie.

This fold took me the best part of the weekend to complete, and I used a little glue (shhhh!) to tidy gaping seams and a little MC to stabilise his (? only they would know the gender) posture and basic body morphology.

Satoshi Kamiya's Bahamut Scale and detail

If I were to fold this again I would use thinner prettier paper, but there are sections where front and back are visible, so the model is not really suited to duo paper – perhaps double tissue or unryu. I had forgotten how satisfying Satoshi Kamiya models are to fold, and how wonderful it is to just get lost in the folding process (I took no progress pics, soz) – it was terrific paper-based therapy. There are so many complex techniques here to isolate and separate body elements, genius design indeed.

985: Satoshi Kamiya’s Ryu Jin 2.1

| wonko

Some folds are quite the journey, Ryu Jins are no exception. I have already folded the 1.2 and the 3.5, but had not tried the 2.1, relegating it to the “when I have time” pile:

2 point 1 - model

Holiday time is a time of recharge, paper folding therapy is my thing so I embarked on the super-duper-complex journey with HUGE bits of paper. I decided to fold it in 2 halves (two 140 x 70 cm rectangles of red duo Ikea Kraft paper).

2 point 1 - CP

As a bit of paper engineering, Ryu are masterpieces of fitting so much on a single square. The 2.1 is laid out in a similar morphology to the 3.5, with 2 halves of the model on opposite edges of the paper. The Ryu 1.2, in contrast, uses the diagonal and is symmetrical about that.

Continue reading →

983: Ryu Jin 2.1 – Tail

| wonko

I have begun the (some say perilous) journey to realise Satoshi Kamiya’s Ryu Jin 2.1. I have previously achieved the head of this model, and there is more work to do to become familiar with the other components, but this is a nice next step:

2.1 tail

The tail of the 2.1 is different to the 1.2 and the 3.5 in that it is more of a fan blade, to get there, you need to fold a small section of the scale field, and pack away a bunch of the paper inside the body.

Continue reading →

982: Satoshi Kamiya’s “Tiger”

| wonko

I have been on a mission for months now to try and render a tiger as realistically as I can in paper. Apart from being feline in shape, tigers have stripes – finding a model that has these stripes was difficult:

Kamiya's Tiger

I bought Satoshi Kamiya’s latest book because of the tiger diagrams it contained – on flicking through the 200+ steps I initially thought it too difficult to try. But try I did, initially with large format red-natural Ikea Kraft paper. I was surprised that I was able to make it through the most torturous steps, so set about re-folding it with black/natural, ensuring the black was the stripes, natural was the residual body colour.

The genius of this design is the subtle and precise control of both sides of the sheet – the stripes are the result of folds, not cuts. The model requires you manipulate raw edges (the sheet border) fan-folded, while wrestling all the other details (legs, head, tail) from the INSIDE of the sheet – quite amazing.

Continue reading →